Decade counter circuit is a befungsi electronic circuit to perform a sequence of numerical calculations either forward or backward calculation. What is meant by forward calculation is where the circuit will count ranging from small numbers to larger numbers. While the countdown to the contrary. Calculations can reach an unlimited number of circuits or design depending on the demands.
A lot of the usability of this counter circuit in the world of digital electronics. It could even be said to be an integral digital electronics with a series of counters. Almost all digital circuits require a series of counters. That's because to implement the functions of numerical or mathematical operations must use the functions of the counter circuit.
For the decade counter circuit above is the use of the family of CMOS IC. Where for all types of CMOS IC can use a maximum supply voltage of 15 volts, whereas TTL only have a maximum supply voltage of 5 volts. Then, using 74ls48-74ls90 as the decade counter IC you no longer need to use as an interface to the decoder IC 7-segment. Because the output generated by the 74ls48-74ls90 has been adapted to the conditions and functions of the seven segment.
Deliberate use of the above series of ignition Schmitt Trigger gate as a damper mechanical switch bounce of the beat. You may not use the gate Schmitt trigger input and switch directly connects to the clock pin IC 4026. Counter circuit you will keep running, but you will find a hopping chopped or shredded irregular.
Tuesday, February 14, 2012
Monday, February 13, 2012
Refrigerator Alarm schematic
Refrigerator Alarm circuit, so that we know whether the fridge is closed or not. Refrigerator sometimes likes to play or open the lid by the children, and this resulted in a refrigerator at room temperature decreases and will increase the electrical load, so that the electricity to be extravagant. Therefore it is necessary alarm circuit.
Circuit placement and How it Works: This circuit is stored into a small box, placed in the fridge near the lamp (if any) or the opening. With the door closed in the refrigerator in the dark, the photo resistor R2 presents a high resistance (> 200K) thus clamping IC1 by holding pin 12 high. When a beam of light came when opening, or a refrigerator light bulbs, photo resistor lowers resistance (<2K), pin 12 so low, IC1 starts counting after a predetermined delay (20 seconds) piezo sounder beeps sound for 20 seconds. then stopped during the same time interval and the cycle repeats until the fridge door closed. D2 is connected to pin 6 of IC1 allows the piezo sounder beeps sound 3 times per second.
List of Components:
R1 10K 1/4W Resistor
R2 Photo resistor (any type)
R3 R4 100K 1/4W Resistors
C1 10nF 63V Polyester Capacitor
C2 100µF 25V Electrolytic Capacitor
D1,D2 1N4148 75V 150mA Diodes
IC1 4060 14 stage ripple counter and oscillator IC
Q1 BC337 45V 800mA NPN Transistor
BZ1 Piezo sounder (incorporating 3KHz oscillator)
SW1_________Miniature SPST slide Switch
B1 _________3V Battery (2 AA 1.5V Cells in series)
Alarm circuit schematic drawings Refrigerator
Circuit placement and How it Works: This circuit is stored into a small box, placed in the fridge near the lamp (if any) or the opening. With the door closed in the refrigerator in the dark, the photo resistor R2 presents a high resistance (> 200K) thus clamping IC1 by holding pin 12 high. When a beam of light came when opening, or a refrigerator light bulbs, photo resistor lowers resistance (<2K), pin 12 so low, IC1 starts counting after a predetermined delay (20 seconds) piezo sounder beeps sound for 20 seconds. then stopped during the same time interval and the cycle repeats until the fridge door closed. D2 is connected to pin 6 of IC1 allows the piezo sounder beeps sound 3 times per second.
List of Components:
R1 10K 1/4W Resistor
R2 Photo resistor (any type)
R3 R4 100K 1/4W Resistors
C1 10nF 63V Polyester Capacitor
C2 100µF 25V Electrolytic Capacitor
D1,D2 1N4148 75V 150mA Diodes
IC1 4060 14 stage ripple counter and oscillator IC
Q1 BC337 45V 800mA NPN Transistor
BZ1 Piezo sounder (incorporating 3KHz oscillator)
SW1_________Miniature SPST slide Switch
B1 _________3V Battery (2 AA 1.5V Cells in series)
Monday, January 9, 2012
Solar Charger Schematic
To take advantage of sunlight shining on the earth can continue to be utilized to serve as a power source so that we can at least save on electricity prices continuing to rise, below is one of a series of simple power plant can be created and used to fill your motorcycle battery or for emergency lights.
How it Works series:
Sunlight is received by the solar panels are then processed into electricity, but electricity generated from each panel is still too small where the 8 Cell Panel arranged in series only mrnghasilkan voltage of approximately 4 volts with a current 200 mA.nah therefore required an electronic circuit to increase the voltage and current enough to be used as a Battery Charger.Electronic Rangakain act as a series of DC to DC Inverter (DC to DC Inverter), which was built by two pieces of Capacitor, Resistor 1, a transistor, a diode, and a coil which is the point of the creation of this series.
The circuit was built with a single oscillator system (blocking oscillator) which was built by the transistor and a coil in which the primary winding totaling 45 turns and 15 turns in the secondary as feedback to provide the voltage at the base of the transistor output of the primary winding connected to the diode and used to The battery charging.When the circuit is coupled with the Emergency Neon Lights will certainly get enough voltage to light at night for free. because its batteries during the day in charge by the sun.
How it Works series:
Sunlight is received by the solar panels are then processed into electricity, but electricity generated from each panel is still too small where the 8 Cell Panel arranged in series only mrnghasilkan voltage of approximately 4 volts with a current 200 mA.nah therefore required an electronic circuit to increase the voltage and current enough to be used as a Battery Charger.Electronic Rangakain act as a series of DC to DC Inverter (DC to DC Inverter), which was built by two pieces of Capacitor, Resistor 1, a transistor, a diode, and a coil which is the point of the creation of this series.
The circuit was built with a single oscillator system (blocking oscillator) which was built by the transistor and a coil in which the primary winding totaling 45 turns and 15 turns in the secondary as feedback to provide the voltage at the base of the transistor output of the primary winding connected to the diode and used to The battery charging.When the circuit is coupled with the Emergency Neon Lights will certainly get enough voltage to light at night for free. because its batteries during the day in charge by the sun.
Tuesday, January 3, 2012
Car Speed Alarm Schematic
When we are driving sometimes we do not know the speed of our car, especially when we are in the course of the highway so nice and straight, if the car's speed is too fast or faster than anyone could lead to accidents that do not want to happen. The circuit then requires the Car Speed Alarm is to alert the driver who did not notice the speed because the roads are nice and straight. Even this series can be set speed, for example, we set when exceeded 100km/h the alarm should sound.
The workings of the circuit:A piezo buzzer will sound. Speed pulse is inserted into the base of Q1 and the resulting waveform at the collector is fed through a RC network to the input of an LM2917 frequency to voltage converter, IC1. The resulting voltage is fed to three comparators (IC2d-IC2b) which has a reference voltage at the inverting input they are set by the 10-turn trimpots VR1, VR2 and VR3. The output of each comparator is applied through another RC network to the gate of an SCR. Anode of the three SCRs are commoned comparator inverting input connected to the left, IC2a.Non-inverting input is set to 2.3 V with a trimpot VR4. In use, once you exceed the speed setting for the comparator in particular, relating SCR to briefly pull the pin 2 of IC2a low and short beep is emitted by a piezo buzzer. Then, if you exceed the speed setting that followed, another beep will be heard. The idea is to make each setting speed of several km / h higher than it actually is, so if you are driving at the correct speed in a particular zone, the buzzer will not sound. But as you increase speed, the buzzer will beep once because you exceed the speed settings for each zone. In this way, there is no need to constantly switch setting the pace as you pass through different zones and you can choose to ignore the beep is not "illegal".
The workings of the circuit:A piezo buzzer will sound. Speed pulse is inserted into the base of Q1 and the resulting waveform at the collector is fed through a RC network to the input of an LM2917 frequency to voltage converter, IC1. The resulting voltage is fed to three comparators (IC2d-IC2b) which has a reference voltage at the inverting input they are set by the 10-turn trimpots VR1, VR2 and VR3. The output of each comparator is applied through another RC network to the gate of an SCR. Anode of the three SCRs are commoned comparator inverting input connected to the left, IC2a.Non-inverting input is set to 2.3 V with a trimpot VR4. In use, once you exceed the speed setting for the comparator in particular, relating SCR to briefly pull the pin 2 of IC2a low and short beep is emitted by a piezo buzzer. Then, if you exceed the speed setting that followed, another beep will be heard. The idea is to make each setting speed of several km / h higher than it actually is, so if you are driving at the correct speed in a particular zone, the buzzer will not sound. But as you increase speed, the buzzer will beep once because you exceed the speed settings for each zone. In this way, there is no need to constantly switch setting the pace as you pass through different zones and you can choose to ignore the beep is not "illegal".
Wednesday, June 8, 2011
Digital Anemometer Schematic
The series is a series of electronic digital anemometer to measure wind speed that is widely used in the field of Meteorology and Geophysics Agency or weather station. The name of this tool comes from the Greek word Anemos, which means wind. The first designers of this tool is Leon Battista Alberti in 1450. In addition to measuring wind speed, the tool also can measure the magnitude of the wind pressure.
As we know, wind is air that moves from one place to another. The wind blows because some parts of the world gets more sun than anywhere else. Land surface air temperature in the heat makes it rise. As a result, the air expands and becomes lighter. Because it is lighter than the surrounding air, the air will rise. Once the heat was rising, its place was soon replaced by the surrounding air, especially from the air above the cooler and heavier. This process occurs continuously, as a result we can feel the movement of air or what we call wind.
Anemometer is designed to measure and record wind speed distribution of 0-17 meters per second +. It was designed for high reliability, ease of construction, and for a wide range of environments. Data logged for 30.46 days (1/12 of one year), and then stored for 11 months. Data can be retrieved with a laptop computer at any time within 12 months of logging. Windmeter is self powered by a solar panel and battery.
As we know, wind is air that moves from one place to another. The wind blows because some parts of the world gets more sun than anywhere else. Land surface air temperature in the heat makes it rise. As a result, the air expands and becomes lighter. Because it is lighter than the surrounding air, the air will rise. Once the heat was rising, its place was soon replaced by the surrounding air, especially from the air above the cooler and heavier. This process occurs continuously, as a result we can feel the movement of air or what we call wind.
Anemometer is designed to measure and record wind speed distribution of 0-17 meters per second +. It was designed for high reliability, ease of construction, and for a wide range of environments. Data logged for 30.46 days (1/12 of one year), and then stored for 11 months. Data can be retrieved with a laptop computer at any time within 12 months of logging. Windmeter is self powered by a solar panel and battery.
Subscribe to:
Posts (Atom)







