Car Parking Sensor schematic

This circuit can be used for an assist in parking the car near the garage wall backing up Pls. LED D7 illuminates Pls bumper-wall distance is about 20 cm., D7 + D6 illuminate at about 10 cm. and D7 + D6 + D5 at about 6 cm. In this manner you are alerted Pls approaching too close to the wall.

All distances mentioned before can vary, depending on infra-red transmitting and receiving LEDs used and are mostly affected by the color of the reflecting surface. Black surfaces lower greatly the device sensitivity. Obviously, you can use this circuit in other applications like liquids level detection, proximity devices etc.

Note:
The infra-red Photo Diode D2, should be of the type incorporating an optical sunlight filter: these components appear in black plastic cases. Some of them resemble TO92 transistors: in this case, please note that the sensitive surface is the curved, not the flat one.
Avoid sun or artificial light hitting directly D1 & D2.
If your car has black bumpers, you can line-up the infra-red diodes with the (mostly white) license or number plate.
It is wiser to place all the circuitry near the infra-red LEDs in a small box. The 3 signaling LEDs can be placed far from the main box at an height making them well visible by the car driver.
The best setup is obtained bringing D2 nearer to D1 (without a reflecting object) until D5 illuminates; then moving it a bit until D5 is clearly off. Usually D1-D2 optimum distance lies in the range 1.5-3 cm.

part list:
R1 : 10K R2,R5,R6,R9 : 1K R3 : 33R R4,R11 : 1M R7 : 4K7 R8 : 1K5 R10,R12-R14 : 1K C1,C4 : 1µF/63V C2 : 47pF C3,C5 : 100µF D1 : Infra-red LED D2 : Infra-red Photo Diode (see Notes) D3,D4 : 1N4148 D5-7 : LEDs (Any color and size) IC1 : NE555 IC2 : LM324 IC3 : LM7812

Low Voltage Monitor schematic

Low Voltage Monitor circuit is highly desirable for security and protection against everyday damage your equipment, especially for your favorite car. This circuit may be very simple / very simple to make because only by using ic LM339. The workings of this circuit is Buzzer will sound and lights Led will light up when your car battery in a state of tension is very minimal. Although the circuit is very simple but can protect your car from damage that would be very detrimental. This voltage monitor circuit may be beneficial to you.

Component List:

R1, R3 2 1K 1/4W Resistor
R2 1 5K Pot
U1 1 LM339 Voltage comparator IC
D1 1 1N5233B Zener Diode
D2 1 LED
BZ1 1 Piezo Buzzer
MISC 1 Board, wire, socket for IC

Notes
1. The circuit will operate from 9V to 12V.
2. Adjust R2 until the alarm goes off at the correct voltage.

Digital Decade Counter Schematic

Decade counter circuit is a befungsi electronic circuit to perform a sequence of numerical calculations either forward or backward calculation. What is meant by forward calculation is where the circuit will count ranging from small numbers to larger numbers. While the countdown to the contrary. Calculations can reach an unlimited number of circuits or design depending on the demands.

A lot of the usability of this counter circuit in the world of digital electronics. It could even be said to be an integral digital electronics with a series of counters. Almost all digital circuits require a series of counters. That's because to implement the functions of numerical or mathematical operations must use the functions of the counter circuit.

For the decade counter circuit above is the use of the family of CMOS IC. Where for all types of CMOS IC can use a maximum supply voltage of 15 volts, whereas TTL only have a maximum supply voltage of 5 volts. Then, using 74ls48-74ls90 as the decade counter IC you no longer need to use as an interface to the decoder IC 7-segment. Because the output generated by the 74ls48-74ls90 has been adapted to the conditions and functions of the seven segment.




Deliberate use of the above series of ignition Schmitt Trigger gate as a damper mechanical switch bounce of the beat. You may not use the gate Schmitt trigger input and switch directly connects to the clock pin IC 4026. Counter circuit you will keep running, but you will find a hopping chopped or shredded irregular.
 

Refrigerator Alarm schematic

Refrigerator Alarm circuit, so that we know whether the fridge is closed or not. Refrigerator sometimes likes to play or open the lid by the children, and this resulted in a refrigerator at room temperature decreases and will increase the electrical load, so that the electricity to be extravagant. Therefore it is necessary alarm circuit.

Alarm circuit schematic drawings Refrigerator

Circuit placement and How it Works: This circuit is stored into a small box, placed in the fridge near the lamp (if any) or the opening. With the door closed in the refrigerator in the dark, the photo resistor R2 presents a high resistance (> 200K) thus clamping IC1 by holding pin 12 high. When a beam of light came when opening, or a refrigerator light bulbs, photo resistor lowers resistance (<2K), pin 12 so low, IC1 starts counting after a predetermined delay (20 seconds) piezo sounder beeps sound for 20 seconds. then stopped during the same time interval and the cycle repeats until the fridge door closed. D2 is connected to pin 6 of IC1 allows the piezo sounder beeps sound 3 times per second.

List of Components:

R1 10K 1/4W Resistor
R2 Photo resistor (any type)
R3 R4 100K 1/4W Resistors
C1 10nF 63V Polyester Capacitor
C2 100µF 25V Electrolytic Capacitor
D1,D2 1N4148 75V 150mA Diodes
IC1 4060 14 stage ripple counter and oscillator IC
Q1 BC337 45V 800mA NPN Transistor
BZ1 Piezo sounder (incorporating 3KHz oscillator)
SW1_________Miniature SPST slide Switch
B1   _________3V Battery (2 AA 1.5V Cells in series)

Solar Charger Schematic

To take advantage of sunlight shining on the earth can continue to be utilized to serve as a power source so that we can at least save on electricity prices continuing to rise, below is one of a series of simple power plant can be created and used to fill your motorcycle battery or for emergency lights.

How it Works series:
Sunlight is received by the solar panels are then processed into electricity, but electricity generated from each panel is still too small where the 8 Cell Panel arranged in series only mrnghasilkan voltage of approximately 4 volts with a current 200 mA.nah therefore required an electronic circuit to increase the voltage and current enough to be used as a Battery Charger.Electronic Rangakain act as a series of DC to DC Inverter (DC to DC Inverter), which was built by two pieces of Capacitor, Resistor 1, a transistor, a diode, and a coil which is the point of the creation of this series.

The circuit was built with a single oscillator system (blocking oscillator) which was built by the transistor and a coil in which the primary winding totaling 45 turns and 15 turns in the secondary as feedback to provide the voltage at the base of the transistor output of the primary winding connected to the diode and used to The battery charging.When the circuit is coupled with the Emergency Neon Lights will certainly get enough voltage to light at night for free. because its batteries during the day in charge by the sun.